Galin powder coating/spray/paint mother board/
printed circuit board/PCB (ESP108) |
For powder coating machine (ESP101)
| GALIN POWDER COATING PCB (108) ELECTRICAL DATA |
| Nominal input voltage |
220V (100V-240VAC) |
| Frequency |
50/60 Hz |
| Input power |
50 VA |
| Rated output voltage |
12~18VPP |
| Rated output current |
1.2A |
| Protection type |
IP54 |
| Temperature rang |
+10ºC to +40ºC
(+50ºF to +104ºF) |
| Solenoid Valve Voltage |
24VDC |
| Gun output voltage |
0-100KVDC |
| Gun output current |
0-100μA |
| GALIN POWDER COATING PCB (108) PNEUMATICAL DATA |
| MAX.input pressure |
8bar |
| MIN.input pressure |
5bar |
| Output pressure |
0~8bar |
| Max.water vapor content of the compressed air |
1.3g/m³ |
| Max.oil vapor content of the compressed air |
0.1mg/m³ |
| Max.compressed air consumption |
19Nm³/h |
| ADVANTAGE OF POWDER COATING PCB (108) OF MACHINE |
Combines the advantages of imported circuit, the use of imported components, according to the environment and conditions were optimized: Product small power consumption, stable and reliable performance, with automatic gain and warning devices, automatically adjust the electric field energy and has automatic protection function, for dead on the powder have an extremely high rate.
Main parameters:
1. size: 160 x 110 x 55mm
2. weight: 230 grams
3. power supply: 13V AC (need power - 30W); 18V AC (need power - 10W)
4. module working power supply: 9.5V 12V - DC; frequency: 26KHz
5. control board operating current: 400mA - 700mA
6. high voltage module: working current 0 - 150uA;
working voltage: 0 - negative 100KV
| APPLICATION AREA OF POWDER COATING MACHIEN |
Galin powder coating machine can be used for Hub
Galin powder coating machine can be used for Furnitur
Galin powder coating machine can be used for Metal Rail
Galin powder coating machine can be used for Metal products
Galin powder coating machine can be used for Glass products
Galin powder coating machine can be used for Metal or Glass Cup
Galin powder coating machine can be used for Any Metal or Glass you want
Galin powder coating machine (ESP101) can be used for Large and Flat piece
Galin Manual powder coating machine (ESP101) can be used for Mass Production
| ATTENTIONS OF POWDER COATING MACHINE |
CLEANING AND MAINTENANCE
Daily Maintenance
1. Clean the injector
2. Clean the powder gun
3. Clean the powder hose and suction unit
Weekly Maintenance
1. Clean suction unit,injector,Powder Clean module and powder gun
2. Check the control unit grounding connections to the coating booth bolts,
the suspension devices of the work pieces,or the conveyor.
TROUBLESHOOTING GUIDE
If the powder gun does not spray powder although the control unit is switched on,then the injector can be dirty or clogged.
| Error/cause |
Troubleshooting |
Injector nozzle, non-return valve unit, powder hose or
powder gun are clogged |
Clean the corresponding parts and if necessary,replace them |
| Conveying vacuum too low |
Increase the powder quantity and/ or total air volume on the control unit |
Insert sleeve worn ,
not or incorrect inserted |
Replace or insert it ,observe the indexing cam |
Insert sleeve is worm after
a short operating duration |
Clean the nozzle ,if damaged,replaced it |
The gun does not spray powder although the control unit
is switched on and the
gun trigger is pressed |
1.Connect the equipment to the compressed air
2.Clean /Replace
3.Clean the corresponding
4.Contact Galin representative |
| COMPANY INFORMATION OF GALIN |
){kind=link}