Galin Lab Powder Coating/Spray/Paint Machine TCL-32 with Manual Gun & hopper / cup
| GALIN POWDER COATING MACHINE (TCL-32) ELECTRICAL DATA |
| Nominal input voltage |
220V (100V-240VAC) |
| Frequency |
50/60 Hz |
| Input power |
40 VA |
| Rated output voltage(to gun) |
12~18VPP |
| Rated output frequency(to gun) |
About20KHZ |
| Protection type |
IP54 |
| Temperature rang |
+10ºC to +40ºC
(+50ºF to +104ºF) |
| Solenoid Valve Voltage |
24VDC |
| Gun output voltage |
0-100KVDC |
| Gun output current |
0-100μA |
| GALIN POWDER COATING MACHINE (TCL-32) PNEUMATICAL DATA |
| MAX.Input pressure |
8bar |
| MIN.Input pressure |
5bar |
| Output pressure |
0~8bar |
| Max.Water vapor content of the compressed air |
1.3g/m³ |
| Max.Oil vapor content of the compressed air |
0.1mg/m³ |
| Max.Compressed air consumption |
19Nm³/h |
| GALIN POWDER COATING MACHINE (TCL-32) GUN PARAMETER |
| Input |
12~18VPP |
| Voltage Frequency |
Around 22KHZ |
| Input Current |
<0.5A |
| Output Voltage |
15~100KV Negative |
| Max.Output powder volume |
Around 600G/MIN |
| Gun cable |
4 M |
| Gun weight |
425g |
| ADVANTAGE OF POWDER COATING MACHINE TCL-32 |
Ideal for good coating grooves and corners.
It has three modes - FLAT MODE,CORNER MODE,RE-COAT MODE.
Powder ascending rate reach up to 65%~85% with long service life.
That is more convenient to operate after the selected mode
| APPLICATION AREA OF POWDER COATING MACHIEN(TCL-32) |
Galin powder coating machine can be used for Hub
Galin powder coating machine can be used for Furnitur
Galin powder coating machine can be used for Metal Rail
Galin powder coating machine can be used for Metal products
Galin powder coating machine can be used for Glass products
Galin powder coating machine can be used for Metal or Glass Cup
Galin powder coating machine can be used for Any Metal or Glass you want
Galin Manual powder coating machine (TCL-32) can be used for Grooves and Corners
Galin Manual powder coating machine (TCL-32) can be used for Complex and Difficult Workpiece
| DELIVERY & PACKING OF POWDER COATING MACHINE(TCL-32) |
| Control Panel with All Kinds Of Connectors |
1 Set |
| Manual Coating Gun with Round Nozzle with Cable |
1 Set |
| Injector |
1 Set |
| Powder Hose |
1 Set |
| Air Tube |
1 Set |
| 304 Stainless Hopper |
1 Set |
| ATTENTIONS OF POWDER COATING MACHINE(TCL-32) |
CLEANING AND MAINTENANCE
Daily Maintenance
1. Clean the injector
2. Clean the powder gun
3. Clean the powder hose and suction unit
Weekly Maintenance
1. Clean suction unit,injector,Powder Clean module and powder gun
2. Check the control unit grounding connections to the coating booth bolts,
the suspension devices of the work pieces,or the conveyor.
TROUBLESHOOTING GUIDE
If the powder gun does not spray powder although the control unit is switched on,then the injector can be dirty or clogged.
| Error/cause |
Troubleshooting |
Injector nozzle, non-return valve unit, powder hose or
powder gun are clogged |
Clean the corresponding parts and if necessary,replace them |
| Conveying vacuum too low |
Increase the powder quantity and/ or total air volume
on the control unit |
Insert sleeve worn,
not or incorrect inserted |
Replace or insert it ,observe the indexing cam |
Insert sleeve is worm after
a short operating duration |
Clean the nozzle ,if damaged,replaced it |
The gun does not spray powder although the control unit is switched on and the
gun trigger is pressed |
1.Connect the equipment to the compressed air
2.Clean /Replace
3.Clean the corresponding
4.Contact Galin representative |
| COMPANY INFORMATION OF GALIN |
){kind=link}