Galin Metal/Plastic Powder Coating/Spray/Paint Mother Board/Mainboard /PCB (CG09) for Galin Optiflex 2f LED

• Customization: Available
• Warranty: 12months
• Type Machine: Manual Powder Coating Machine
• Model NO.: CG09
• Type Gun: Manual and Auto Powder Coating Gun
• Type of Shipping: Express/Air Transport/Land Transpor/Ocean Shipping
• Delivery Detail: Shipped in 5 Days After Payment
• Match Machine: Gema Optiflex
• Type: Electrostatic Spraying Equipment
• Application: Hardware Spraying Equipment, Metal and Glass Spraying Equipment
• Coating: Powder
• Certification: CE
• Method Type: Manual
• Condition: New
• After-sales Service: Online
• Transport Package: Carton, High-Strength Cardboard
• Specification: Normal
• Trademark: Customized/Galin/Gema
• Origin: Shandong, China
• HS Code: 8424909000
• Production Capacity: 100 Sets/Month

Product Description

Galin Powder Coating PCB / Mainboard (CG09)
for Galin OptiFlex 2F

IT USE WITH LED SCREEN
ITS POWDER ASCENDING RATE REACH UP TO 85%~95%
 

CG09 PCB spare parts
CG09 Gun control unit - complete	1008 780
Cover	1008 301
1 Motor throttle for Fluidizing air                                  - complete	1008 012
2 Fluidizing pad - 1/8"a	237 264
3 Distribution block - complete	1007 036
4 Solenoid valve             - Ø 8-Ø 8 NW3.4, 24 VDC	1003 914
5 Motor throttle for Transport air, Spraying air or Electrode rinsing air                                  - complete	1000 064
6 O-ring - Ø 12x1.5 mm, NBR70	261 416
7 Rear panel gasket	1007 033

Powder coating PCB CG09 electrical data

Nominal input voltage	110V240VAC
Frequency	50-60Hz
Connected load (without vibrator)	140 VA
Nominal output voltage (to the gun)	eff.10 V
Nominal output current (to the gun)	max. 1.2 A
Connection and output for vibrator(on Aux output)	110/230 VAC max. 100 W
Connection for rinsing function(valve)	24 VDC max. 3 W
Temperature range	0°C - +40ºC (+32°F - +104°F)
Max. surface temperature	120 °C (+248 °F)
Approvals	II 3 D IP54 120 °C

Powder coating PCB CG09 Pneumatical data

MAX.input pressure	10bar
MIN.input pressure	6bar
Input pressure (Dynamic based on pressure regulator setting)	5.5 bar / 80 psi
Max.water vapor content of the compressed air	1.3g/Nm³
Max.oil vapor content of the compressed air	0.1mg/Nm³
Max.compressed air consumption	8Nm³/h

GALIN POWDER COATING PCB (CG09) PROCESSIBLE POWDER
Plastic Powder:	√
Metallic Powder:	√
Enamel Powder:	×

 

Galin powder coating PCB can be used for Hub
Galin powder coating PCB can be used for Furnitur
Galin powder coating PCB can be used for Metal Rail
Galin powder coating PCB can be used for Metal products
Galin powder coating PCB can be used for Glass products
Galin powder coating PCB can be used for Metal or Glass Cup
Galin powder coating PCB can be used for Any Metal or Glass you want

Galin Matel/Plastic powder coating PCB (CG09) can be used for Metal Powder

Galin Matel/Plastic powder coating PCB (CG09) can be used for  Complex Piece

CLEANING AND MAINTENANCE OF POWDER COATING MACHINE
(OPTFLEX-2F WITH LED SCREEN)

1. Daily Maintenance

  1. Clean the injector
  2. Clean the powder gun
  3. Clean the powder hose and suction unit

1. Weekly Maintenance

  1. Clean suction unit,injector,Powder Clean module and powder gun
  2. Check the control unit grounding connections to the coating booth bolts,
     the suspension devices of the work pieces,or the conveyor.


TROUBLESHOOTING GUIDE OF POWDER COATING MACHINE(OPTIFLEX-2F)

If the powder gun does not spray powder although the control unit is switched on,then the injector can be dirty or clogged.
 

Error/cause	Troubleshooting
Injector nozzle, non-return valve unit, powder hose or powder gun are clogged	Clean the corresponding parts and if necessary,replace them
Conveying vacuum too low	Increase the powder quantity and/ or total air volume on the control unit
Insert sleeve worn ,  not or incorrect inserted	Replace or insert it ,observe the indexing cam
Insert sleeve is worm after a short operating duration	Clean the nozzle ,if damaged,replaced it
The gun does not spray powder although the control unit  is switched on and the  gun trigger is pressed	1.Connect the machine to the compressed air    2.Clean /Replace                                             3.Clean the corresponding                               4.Contact Galin representative